OEM fault-code index 17,638 model-code entries · 138 manual P/Ns

Arctic Cat · 2027 · C/P/U DTC

2027 Arctic Cat 400 (Bearcat, Jag, M, Pantera, XF) fault codes

The 2027 Arctic Cat 400 Operator's Manual publishes one 39-entry diagnostic table for six 400-class snowmobile models. The table is mostly P-codes, with four U-codes and no C-codes. This page lists all 39 rows in the manual's printed order.

39 OEM-listed entries C/P/U DTC format Source: OEM manual

Scope note

Built from the 2027 400 Operator's Manual (P/N 653-00129), General Information / Diagnostic Codes, printed p. 11.

The manual covers six models: Bearcat 400 LT, Jag 400, Jag 400 Special, M 400, Pantera 400, and XF 400.

The table has 39 rows: 35 P-codes and 4 U-codes. It has no C-codes and no FUEL OFF row.

38 of the 39 rows also appear in the 600.858 table. P2600, Coolant Pump “A” Control Circuit/Open, is the only row unique to the 400 book.

The 400 manual has no EPS table. The 600.858 and 4 Stroke EPS tables are covered on the shared snowmobile EPS page.

Table profile

This page reproduces 39 entries from the 2027 Arctic Cat 400 (Bearcat, Jag, M, Pantera, XF) owner’s manual and manual P/N 653-00129.

Rows keep the manual’s printed order, from P0112 to U1001.

The table uses manufacturer codes rather than SPN/FMI pairs. The printed codes group into 35 P-codes and 4 U-codes.

Every printed code carries one title in this table.

These counts describe the rows on this page, not every manual in the archive. The source box below lists the exact citation for every record on the page.

What the 39 rows contain

The P block has 35 rows. It covers intake-air and coolant temperature, throttle position, engine over-temperature, cylinder 1 injector, knock control, ignition coil A, exhaust temperature, oil-pump and injector programming, regulator and fuel-pump voltage, oil-pump outlier, speed sensor, knock activation, crank-angle sensor, exhaust-valve position and actuator, engine RPM, barometric pressure, P2600 coolant-pump control, and control-module shutdown. The U block has 4 rows: lost communication with the suspension control module and the LCD gauge, plus vehicle registration messages.

P2600 is the row that separates this table from the 600.858 sequence. The manual prints the description with quotation marks around “A” and a slash between “Circuit” and “Open”; the page preserves that text.

The six 400 models behind one book

Bearcat 400 LT and Pantera 400 are the utility and touring names; Jag 400, Jag 400 Special, M 400, and XF 400 cover the trail and crossover names. The manual prints one table for all six. The page keeps the full table rather than inferring which rows a particular model can set.

How the 400 table relates to the 600.858 table

The 400 table is nearly a subset of the 600.858 table. 38 of its 39 codes appear in the 600.858 sequence; P2600 is the only addition. The 600.858 book prints 28 codes that the 400 book does not, including the C-family suspension and warmer rows and the exhaust-valve, navigation-display, and P1004/P1261/P1264 rows. The 400 page stays separate because the book, model list, and citation are different.

What the table does not include

The table prints a code and a short description only. It does not print an SPN/FMI pair, a fault-setting condition, a healing condition, a wiring diagram, a test procedure, or a parts list. The page therefore has no FMI glossary and no condition columns. It also does not expand a code into a repair step or a safety determination.

This book has no EPS table. A C13xx code is not part of this sequence. The 600.858 and 4 Stroke books publish a separate EPS table on the shared snowmobile EPS page.

How to use this page

Record the exact code, confirm the model year and model name, and note the manual P/N and printed page. The table below keeps the manual's order, and the filter can search by code or by a word from the description. The 600.858 page covers the larger main table.

This page is a label index. It does not provide repair steps, parts advice, or a diagnosis for a specific machine. Codes can vary by trim, market, and running changes, so the cited manual remains the source for the exact machine.

Full OEM table

39 entries from the 2027 Arctic Cat 400 (Bearcat, Jag, M, Pantera, XF) owner's manual diagnostic table.

This chapter publishes one description line per code. The description column below keeps the manual's wording.

39 entries
CodeFault description (OEM manual)
P0112 Intake Air Temp Sensor 1 Circuit Low Code page
P0113 Intake Air Temp Sensor 1 Circuit High Code page
P0117 Coolant Temp Sensor 1 Circuit Low Code page
P0118 Coolant Temp Sensor 1 Circuit High Code page
P0122 Throttle Position Sensor Circuit Low Code page
P0123 Throttle Position Sensor Circuit High Code page
P0217 Engine Coolant Over Temp Condition Code page
P0261 Cylinder 1 Injector Circuit Low Code page
P0324 Knock Control System Error
P0327 Knock Control 1 Circuit Low
P0328 Knock Control 1 Circuit High
P0351 Ignition Coil (A) Primary/Secondary
P0545 Exhaust Temp Sensor Circuit Low
P0546 Exhaust Temp Sensor Circuit High
P1000 Oil Pump Flow Not Programmed
P1001 Injector 1 Offset Not Programmed
P1003 Oil Pump Outlier
P1005 Regulator Voltage Circuit Low
P1006 Regulator Voltage Circuit High
P1007 Fuel Pump Circuit Low
P1008 Fuel Pump Circuit High
P1009 Speed Sensor Malfunction
P1324 Knock Control System Activated
P1329 Knock Sensor Loose Detection
P1636 Crank Angle Sensor Circuit
P1639 Exhaust Valve Position Sensor Circuit Low
P1640 Exhaust Valve Position Sensor Circuit High
P1645 Exhaust Valve System Malfunction
P1646 Exhaust Valve Actuator Self-Cleaning Open Error
P1647 Exhaust Valve Actuator Short Error
P1755 Engine RPM Sensor Circuit Malfunction
P2228 Barometric Pressure Sensor (A) Circuit Low
P2229 Barometric Pressure Sensor (A) Circuit High
P2600 Coolant Pump “A” Control Circuit/Open
P3001 Control Module Improper Shutdown
U0132 Lost Communication with Suspension Control Module
U0155 LCD Gauge Communication Lost
U1000 Vehicle Not Registered or Invalid PIN Entered
U1001 Vehicle Not Registered and Vehicle Limits Enabled

Source: Arctic Cat 2027 400 (Bearcat 400 LT, Jag 400, Jag 400 Special, M 400, Pantera 400, XF 400) Operator's Manual - General Information / Diagnostic Codes (P/N 653-00129; printed p. 11). Codes can vary by trim, market, and running changes.

Reading the table

The code column reproduces the printed P/U code. The description column reproduces the manual's short fault description. The table has no SPN/FMI column, no condition or healing column, and no per-row printed page.

A label identifies a monitored circuit or condition. It does not confirm that a named part has failed, and it does not establish whether the machine is safe to operate.

Write down the full code, the model year and model, and the conditions when it appears. That record is what the manual and a service provider use to match the entry to your machine.

Source note

This page publishes short labels from the public OEM owner's manual chapter, not the manual's long-form repair prose. The source box below gives the exact chapter and model-year coverage.

Scope

This is a label index. It does not provide repair procedures, parts advice, or a diagnosis for a specific machine. Codes can vary by trim, market, and running changes.

Common questions

What does this 2027 Arctic Cat 400 (Bearcat, Jag, M, Pantera, XF) table cover?

This page lists 39 code entries from the cited public OEM owner’s manual (Arctic Cat 2027 400 (Bearcat 400 LT, Jag 400, Jag 400 Special, M 400, Pantera 400, XF 400) Operator's Manual - General Information / Diagnostic Codes (P/N 653-00129; printed p. 11)). The table preserves the short condition or component/failure labels published in that owner’s manual.

Where can I check the source?

The source box at the bottom of the page gives the manual P/N, the model-year coverage, and a link to the OEM owner’s manual. The methodology page explains the site’s source and labeling rules.